R-22 Refrigerant Pressure / Temperature Chart & Table Downloads Measure the suction line temperature neaer its entry to the compressor/condenser unit. R-22 Superheat & Sub-Cooling Temperature Range= 8 - 18☏.Table pressure: R-22 High-Side pressure = 150-175 psigĬalculated pressure: R-22 High-Side pressure = (75 x 2) + 50 = 200 psig - you should take this as an upper limit. OPINION: this rule of thumb gives pressures a bit higher than shown in our R-22 pressure and temperature table above. R-22 High-Side pressure = 2 x ambient temperature (F) + 50 psi.So at 80☏ return air temperature, the suction line temperature would be between 40☏ and 45☏ Refrigerant Low-Side Suction Line Temperature: 35-40 ☏ below the building's return air temperature measured at the air handler.Įxample: temperature at the return air entry to the air handler = 80☏.Ĭalculate the evaporation temperature = suction line temperature range: (80☏ - 35☏ = 45☏) - (80☏ - 40☏ = 40☏).Other sources give the low side pressure range = 60 - 80 psig. Varies by indoor wet bulb temperature and outdoor ambient temperature, where higher heat loads increase the vapor line pressure. ![]() R-22 Low-Side Typical Operating Pressure-Range = 58 - 85 psig.R-22 Low-Side Turn-On Pressure = 50 psig (R22 at 30 deg F) is a typical pressure at which the HVACR compressor/condenser will turn-onġ00 psig (R 22 at 85 deg F) is a typical pressure at which the HVACR compressor will turn off.R-22 Low-Side pressure when compressor is OFF = 30 psi at 90☏ ambient temperature, system OFF.Prah, Frank, CMS, "Refrigerant 410A", Refrigeration Service Engineers Society, 1666 Rand Road, Des Plaines IL 60016 USA, Tel: 84, retrieved 9, original source: Low pressure refrigerant switches on Carrier HVACR typically open at 50 psi and close at 100 psi. On a properly-charged and working air conditioning system using R-22 refrigerant R22 Refrigerant Pressure Rules of Thumb Typical Off, Low, High side R22 Pressures & Temperatures These psig readings for R-22 are what you'd expect the pressure of the gas to be in an enclosed container at the temperature given and at steady state.īoth older R-22 and R-134 operate at lower pressures than R-410A. ![]() Typical high side pressure, may vary by equipment.Typical low pressure or suction side, may vary by equipment and metering controls - these are "gauge pressure readings" or "psig".This chart is using outdoor ambient temperature.R22 and other common refrigerants is an odorless, colorless gas that will be liquid at sufficiently low temperature and/or high pressure.R2 status: no longer in active use, replaced with R458A.R22 gas cylinder identification: light green.R22 density: 3.66 g/cm 3, in gas form - this is a colorless gas.R22 boiling point: -40.8 degree Celsius at atmospheric pressure (sea level or 1 ATM).R22 alternative names: CHClF 2 Chlorodifluoromethane, Difluoromonochloromethane, generic term: hydrochlorofluorocarbon (HCFC).R22 temperature/pressure relationship: see the table above.Bar = atmospheres where 1 Bar = 14.5 psig or normal pressure at sea level.R-22 Refrigerant Temperature vs Pressure Data ![]() R 404A and later R407c may replace R22 in some applications.īelow this table of example refrigerant operating pressures for R-22, we provide links to complete refrigerant pressure/temperature charts as PDF files that you can download free. R22 was phased out in 2010 and is no longer widely available. R-22 Refrigerant DataĬFCs, ChloroFluoroCarbons - first generation refrigerants like R22 (1950s & later) were widely used in refrigerators and air conditioners. We also provide an ARTICLE INDEX for this topic, or you can try the page top or bottom SEARCH BOX as a quick way to find information you need. We discuss how to diagnose refrigerant pressure problems how to determine the proper refrigerant charge quantity. This air conditioning repair article series explains how overcharging or undercharging of refrigerant in an air conditioner or heat pump is detected and we list the effects of overcharged or undercharged refrigerant. R-22 refrigerant charge quantity for air conditioners & heat pumps: We have no relationship with advertisers, products, or services discussed at this website. Air Consumption Table (c.f.InspectAPedia tolerates no conflicts of interest. Alternatively use the table below – to determine the cfm required lookup the nozzle size in the left column and the air pressure on the top row.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |